MasterForce 241-0853 Manual do Operador descarregar pdf (Página 7)

4. Press the sandpaper ﬁrmly against a smooth surface for a short period,

then switch on the tool. The burr will form a non-slip bond with the outer

edge of the sandpaper felt. This will avoid premature wear.

5. If one point has become worn, pull off the sandpaper, turn it 120° and

place it on the sanding pad again.

MOUNTING THE FLANGES FOR

DREMEL

BRAND OSCILLATING TOOL

ACCESSORIES (Fig. 9 & 10)

The ﬂange is used as adapter to

permit Dremel

brand oscillating tool

accessories to be mounted on the Utila-

Tool

1. Disconnect the tool from the power

source.

2. Loosen the ﬂange bolt with the hex

key supplied, and remove the ﬂange

and bolt.

3. Put the selected snap-ﬁt accessory

onto the outer ﬂange, making sure

that the accessory engages all 12

pins in the outer ﬂange and the

accessory is ﬂush against the outer

ﬂange, then put the accessory/outer

ﬂange assembly onto the inner

ﬂange.

4. Align the grooves on the inner ﬂange with the four raised ribs on the drive

shaft; put the inner ﬂange onto the drive shaft. Make sure the line on the

side of the inner ﬂange align with the line on side of the drive shaft. (Fig.9)

5. With your gloved hand holding the accessory, attach and tighten the

clamping bolt using the hex key (Fig.10).

NOTE: Some accessories, such as scrapers or blades, may be mounted

either straight on the tool, or at an angle to enhance usability.

OPERATION

WARNING! Use sharp, undamaged saw blades only. Deformed, blunt saw

blades or saw blades that are otherwise damaged can break.

WARNING! For all accessories, work with the accessory away from the

body. Never position hand near or directly in front of working area. Always

hold the tool with both hands and wear protective gloves.

CUTTING

Saw blades are ideal for making precise cuts in tight areas, close to edges

or ﬂush to a surface. Select a medium to high speed for making the initial

plunge; start off at medium speed for increased control. After making your

initial cut, you can increase speed for faster cutting ability.

Plunge cutting blades are intended to make precise cuts to allow for

installation of ﬂooring or wall material. When plunge cutting, it is important

not to force the tool. If you experience a strong vibration in your hand during

the plunge cut, this indicates that you are applying too much pressure. Back

the tool out and let the speed of the tool do the work. While keeping the

teeth of the blade in the work surface, move the back of the tool in a slow

sideways motion. This motion will help expedite the cut.

The Segmented saw blade is ideal for making precise cuts in wood, plaster,

drywall material.

Applications include cutting openings in ﬂooring for venting, repairing

damaged ﬂooring, cutting openings for electrical boxes. The blade works

best on softer woods such as pine. For harder woods, the blade life will be

limited.

Select a medium to high speed.

GROUT REMOVAL

Grout removal blades are ideal for removing damaged or cracked grout.

Grout blades come in different shape to tackle different grout line.

Select a medium to high speed.

To remove the grout, use a back and forth motion, making several passes

along the grout line. The hardness of the grout will dictate how many

passes are needed. Try to keep the grout blade aligned with the grout line

and be careful not to apply too much side pressure on the grout blade

during the process. To control the plunge depth, use the carbide grit line on

the blade as an indicator. Be careful not to plunge beyond the carbide grit

line to avoid damage to the backer board material.

If you notice the blade clogging during the grout removal process, you can

use a brass brush to clean the grit, thus exposing the grit again.

SCRAPING

Scrapers are suitable for removing old coats of varnish or adhesives,

removing bonded carpeting, e.g, on stairs/steps and others mall/medium

Fig.9

Fig.10

1 2 3 4 5 6 7 8 9 10 11

Comentários a estes Manuais

Sem comentários

MasterForce 241-0853 Manual do Operador Página 7

Comentários a estes Manuais